Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75") PNL Liners
Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75") PNL Liners
Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75") PNL Liners
Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75") PNL Liners
Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75") PNL Liners
Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75") PNL Liners

Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75")

Precio de venta$169.09
Cantidad:
Fast Ship: Usually takes 1-2 business days to ship out.
Ships from Utah
(Click for average Ground delivery map )
Ships via FedEx/UPS only

Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75")

  • Length: 15 1/2"  (Across)
  • Width:  10"  (Front-To-Back)
  • Depth: 4 3/4"  (At Drain)
  • Sides have at least a 5° slope to ensure Mold removal from concrete

    Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75"):

    • The 'Small Oval' Sink Mold for concrete sink fabrication.
    • A small oval shaped design for simplicity and where small size is needed.
    • Small style drain for bathroom lavatory size drains. Each Sink Mold comes with a reusable rubber drain plug 1.5" tall and tapered from 1-5/8"to 1-7/8".(you will want to secure this plug with silicone to your sink mold before use, small side should ideally be stuck to the sink mold). 
        • Please note: some metal drain hardware is a larger diameter than 1-5/8" please be sure to check the drain you're going to use for clearance and if you need a larger diameter hole in the concrete then you may consider using something else like a piece of foam to create plug hole.
    • Create a seamless integral concrete sink and counter top, or form around to create a vessel sink.
    • All our molds have Lifetime Guarantee against defect. This Guarantee does not cover misuse of the Molds (Dropping the Mold, Prying the Mold out using a screwdriver, Driving onto it with a truck tire... etc.).
    • Expressions LTD will not be held liable for any damage, misuse, or collateral damages resulting from use of any of our products. If there is a flaw or defect with a product, we will fix or replace the product.

    Mold Use:

    Mold Setup:

    • When planning, remember to add 1" - 2" to each side of the sink to your measurements, to account for the concrete thickness on the sides of the finished sink.
    • Optional- Rubber molds don't 'need' to be waxed, but it can help to make removal easier.  To wax the mold, apply 2-3 coats of Mold Release Wax to the mold, lightly buffing between coats once it hazes.
    • Apply small amounts of silicone to the Mold's bottom, and set in place in your form. Allow silicone to dry.
    • Screws can be used to secure the Mold if necessary. Using screws of the appropriate length, screw through the bottom of the form, up into the bottom of the Sink Mold.
    • Run a smooth silicone bead around perimeter of the Sink Mold, where it meets the form base (using a tool such as our Caulking Ball Tool makes this process very clean and easy). 
    • Apply a thin coat of Rubber Safe Form Release to the Mold just prior to casting the concrete piece.

    Concrete Casting: 

    • Various methods can be used to cast the concrete piece. View our Concrete Recipe section for tips on concrete mixes.
      • GFRC: Cement and fiberglass is sprayed on and hand packed into the form and around the Mold.
      • Wetcast: Oatmeal consistency concrete is placed in form and around the Mold and vibrated. A simple box should be built around the Sink Mold, to contain the concrete during this process.
      • Hand Packed: A drier concrete mix is hand packed into the form and around the Mold. A second step after de-molding will fill the voids with cement slurry, usually of a different coloring.
    • Any voids in the finished concrete can be filled using a Cement Slurry.

    Mold Removal:

    • If the steps above were followed for the Mold Setup, then most Molds will usually pull out of the concrete with little effort.
    • If the mold is difficult to remove, try:
      • Compressed air shot around the Mold rim will break the suction holding the Mold in the concrete.
      • Most Molds can be pushed out of the concrete by removing the drain piece, and pushing the Mold out through the drain slot.

    Clean-up and Care of The Concrete Sink Mold SDP-28 Oval Small (15.5"x10"x4.75"):

    • Clean Mold with a sponge after each use. Any dried cement residue can be removed with a scotch-brite pad (as outlined above in the Mold Setup section. A light muriatic acid wash (20:1, 20 parts water to 1 part muriatic acid) can also remove cement scale.
    • Waxing and buffing the Mold after cleaning it use is recommended to protect the Mold until its next use.

      Customer Reviews

      Based on 1 review
      100%
      (1)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      J
      Jay Osborn
      Excellent results

      Very nice mold that following all instructions performed great. Demold was a snap and results are awesome Thanks.