Concrete Form Liner - 72" x 24" Slate Flagstone Block
- Concrete liner- 24" Slate Flagstone Block formliner.
- Slate, Sandstone, Flagstone style large block liner. Can be cut down with a table saw to create various form sizes (when cutting liners, just make multiple passes on a table saw, cutting about 1/8"-1/4" of the rubber per pass).
- Designed for creating Blocks, Steps, Columns, Fences, etc.
- If making blocks, we do have corner pieces that line up to this mold. Please contact us.
- Made of extremely durable polyurethane that can flex and stay strong.
- Cut to length easily with a utility knife or chop saw. Join cut pieces using silicone.
- Fast and easy to place in a mold, and quick to clean after use.
- Good for hundreds of uses- Actually gets better with each use as they season.
- Weight: 70lbs
- Shipping: Due to weight, this is non-free shipping item, so please order separately from other 'free shipping' items, and shipping will be added at checkout based on your ship-to location.
Specifications Concrete Form Liner - 72" x 24" Slate Flagstone Block
- Measurements: 72"L x 24"H
- *Occasional imperfections may be present on the Edge Form Liners, and can be removed or altered using a sharp utility knife, or a very abrasive sand paper / resin-bound grinding discs.
Concrete Form Liner - 72" x 24" Slate Flagstone Block Setup:
- Form Liners can be curved to form a slight radius. If the Edge Form Liner begins to ripple and distort, then the radius is too tight, so you will need to make the curve radius larger to ensure a smooth, consistent edge detail.
- Form Liners can be cut to fit your form. Cut using a SHARP razor knife, or with a chop saw. Liners can be cut straight, or mitered at angles so they fit tightly in your form.
- Place Form Liner in your form and either silicone in place, nail with a small brad finish nailer, or screw through the backing form into the rubber liner.
- For most applications (Precast), run a silicone a bead across the bottom edge of the Form Liner, up any corners, and across any joined together seams, to create a water-tight seal.
- Use of a polyurethane rubber safe Form Release (sold here) is recommended: Form release helps create a smoother finish on the concrete, less air pockets in the concrete edge, and easier to clean the Form Liners when finished.
- Vibrate concrete well (either vibrating the concrete, or rapidly tapping the edges of the forms with a hammer or palm sander), or use your fingers to compact the concrete against the Form Liner to remove as many air pocket voids as possible.
- After the concrete is sufficiently set up (typically 2-3 days for normal precast concrete), remove the Form Liner.
- If the Form Liner needs to be removed before the concrete is cured (usually only when using on cast in place concrete, such as steps or pool decks), make sure to remove edge slowly, carefully, and make sure you used a good release first!
- Removal is simple- start on one end, and slowly peel the Form Liner away from the concrete.
- Concrete may have small 'bumps' which can be sanded off with quickly with Diamond Sanding Pads (sold here). These bumps tend to disappear the more the Edge Form Liner is used, as it becomes seasoned.
- Fill any air pocket voids with a Concrete Slurry Mix.
Edge Liner Care:
- Clean with a stiff brush and water after each use. Any silicone left on the forms should be peeled or scraped off (the sooner the easier to remove). Any hardened concrete and difficult to remove silicone can usually be removed using a wire brush.
- Muriatic Acid can be used to clean of cement residue from the Edge Form Liners in a 20:1 ratio (20 parts water to 1 part muriatic acid). Rub the Edge Form Liner with a stiff nylon brush and the muriatic acid water. Rinse Form Liner thoroughly with clean water.
- Store Form Liners out of direct sunlight, laid out flat.
- If Form Liners ever get curved or twisted so they don't lay flat naturally, the easiest solution is to lay them out flat on a concrete or asphalt surface on a really hot day and let the sun heat them up, straighten them out, and then when they cool they should hold their shape more naturally.
Videos showing some uses of Edge Form Liners:
Video showing cutting down the height on a Form Liner using a table saw:
Video showing using Form Liners to create steps and bench seating: